How To Use
Interface
Introduction
1、After the device is started, enter into the interface of mode selection (Figure1 as below)
After selecting auto mode or manual mode to enter into figure 2 interface
(Figure 1)
2、 After clicking Auto/Manual in Figure 1, enter into the selection interface of gender/age/position (Figure 2 )
- Choosing the corresponding gender and age；
- After selecting the corresponding part according to the part to be treated, click to enter into the working interface.
(Figure 2)
3、According to the auto selection in Figure 1, click in Figure 2 to enter enter the auto working interface (Figure 3)
(Figure 3）Introduction of auto working interface
- In Figure 3 (Auto mode interface), different modes are selected according to the purpose of body shaping:
【HIIT】：Basic training for novices. 【OBESITY】：Adapt to training.
【SLIGHTLY FAT】：Initial training 【SHAPING】：Advanced training
【Lose Weight】：Professional training
Each mode contains six different frequencies of automatic switching. The first minute of each mode is warming-up.
- In Figure 3 (Auto mode interface), different modes are selected according to the purpose of body shaping:
【Intensity A B】：Handle intensity of A and B，click【-】and【+】to adjust intensity.
【Intensity C D】：Handle intensity of C and D，click【-】and【+】to adjust intensity.
【A-RF】：RF intensity of A handle，【B-RF】：RF intensity of B handle，
click【-】and【+】to adjust intensity.
Before operation,setting the magnetic vibration and RF intensity, It’s recommended to start with a lower intensity and gradually increase it. RF and magnetic vibration intensity should be slowly increased according to the comfort of the customer. As the treatment continues, the energy area will become warmer and the magnetic vibration will gradually become stronger.
- 【Time】: Click [+] and [-] to adjust the working time.
The default working time of system is 30 minutes，click【+】and【-】to adjust. The time range can be adjusted from 5 to 60 minutes, and the operation of each part is about 30 minutes.
Noted: When the device is suspended, click [-] and [+] to adjust the parameters.
4、according to the auto selection in Figure 1, click in Figure 2 to enter into the manual working interface (Figure 4).
(Figure 4) Introduction of manual working interface
5、Manual working interface：Setting intensity（Figure 5）
(Figure 5) Introduction of manual working interface
- Setting the frequency F1-F3, click【+】and【-】to adjust the output frequency, the range as below：
【F1】：The intensity range is 3HZ (weak) to 150Hz (strong);
【F2】：The intensity range is 3HZ (weak) to 150Hz (strong);
【F3】：The intensity range is 3HZ (weak) to 150Hz (strong);
Before operation, set the frequency parameters according to the required frequency. F1 frequency works for 5 minutes, F2 frequency works for 1 minute and F3 frequency works for 5 minutes. F1, F2 and F3 frequencies cycle in turn.
It’s recommended that F1 be set to 50HZ, F2 to 5HZ, and F3 to be set to 150HZ.
- Setting the intensity, rang from 8% (weak) to 100% (strong)
【Intensity A B】：Handle intensity of A and B，click【-】and【+】to adjust intensity
【Intensity C D】：Handle intensity of C and D，click【-】and【+】to adjust intensity.
【A-RF】：RF intensity of A handle,【B-RF】：RF intensity of B handle，click【-】and【+】to adjust
intensity.
Before operation,setting the magnetic vibration and RF intensity, It’s recommended to start with a lower intensity and gradually increase it. RF and magnetic vibration intensity should be slowly increased according to the comfort of the customer. As the treatment continues, the energy area will become warmer and the magnetic vibration will gradually become stronger.
- 【Time】: Click [+] and [-] to adjust the working time.
The default working time of system is 30 minutes，click【+】and【-】to adjust. The time range can be adjusted from 5 to 60 minutes, and the operation of each part is about 30 minutes.
